browneyesvictim:
I will be rigging my new Revo soon. I'm planning on doing the geatrax in the usual spots on both sides of the gunwale for mounting ff and rod holder. I would like to consider adding a sail and furling kit in the near future. Looking at how the factory furling fairlead and ropes go, I'm wondering if there will be room for both. Any advice?
Low_Sky:
I have no first-hand experience with this, but I have been doing the same research you have been doing regarding sailing my new Revo 16. The most useful nugget of wisdom I have found on this is that the Hobie-recommended placement of the furling line fairlead is not exact. It will obviously vary from boat to boat, and can also be re-positioned as needed to clear other gear on your boat. I believe I gleaned that from Matt Miller on the Hobie Forum. Hobie has to prescribe a location in the installation instructions because some people are so mechanically dis-inclined that they would be lost without guidance.
browneyesvictim:
Well, I guess ill find out. I see no reason why I cant mount the fairlead on the geartrax. Ill make a little spacer to mount it on a 45' angle. That should make it adjustable fore and aft, but the rope coming back may interfere with the fish finder. Ironically someone had just posted about this on the Hobie forum: http://www.hobiecat.com/forums/viewtopic.php?f=32&t=57189
I am considering using Yakataks new anchor trolley system components along the side to improve functionality, aesthetics and keep it all tidy. Surely I'm not the first person to have thought of this.
browneyesvictim:
Rigging a new Hobie Revolution 13 with a rollerized sail and furling kit on Gear Tracks.
Although the factory Hobie sailing and furling setup is simple and works, I felt there is a lot left to be desired. I’m upgrading from the factory Hobie hardware to a rollerized pulley system and mounting on modern Yak-Attack GT90 Gear Tracks. I can’t take credit for many of the ideas contained in this article as much of this has been scavenged from around the internet in different applications.
1) Tie downs- I have drilled a hole in the center of all 5 of the threaded tankwell bungee cleats and installed ¼-20 stainless eyebolts with a washer and nylon nut.
2) Furling Kit- The furler is designed to roll up the sail on the mast so you have control of when and how much sail you want to deploy. One association that I made rather quickly was the fact that the furling system shares much of the same concept and needs as an anchor trolley system. So why wouldn’t you want it on rollerized pulleys?
a) Fairlead- The factory Hobie fairlead that comes in the furling kit is just a small double cleat that is supposed to be mounted (permanent) at a 45’ on the gunwale near the mast. This is in a very bad place when using gear tracks and is not easily mounted on gear tracks. I have mounted two Harken 29 Carbo Cheek pulleys on a Yak-Attack JK Hatch Accessory Plate to the forward gear tracks. This keeps the ropes outboard of the hull and away from the rod holder or whatever else gets mounted on the gear tracks. The rope stays alongside the hull, tidy and out of the way! All is good here!
b) The furling rope- By design, the Hobie factory set-up is supposed to just slide through a ring on a bungee at the rear. Again, why wouldn’t you want this on a pulley? I have simply added a Harken Carbo 29 pulley here. Much smoother operation!
c) The furler tension bungee- The hook of the bungee cord is supposed to be attached to a supplied pad eye that is installed at a location somewhere alongside the hull. In my case, the bungee attaches perfectly to the added forward tank well cleat eyebolt. That’s 2 less holes to drill in my boat!
3) Sidekick Ama Mounting- The factory Hobie install uses two 3/8” well nuts per side to mount the sidekick AMA cross bar. I'm not fond of well nuts to begin with, and the bar becomes "permanent". Therefore, I’ve chosen to mount the Sidekick Amas on Yak-Attack 8” GT90 Gear tracks with backing plates.
a) GT90 Gear Track Mounting- Nothing special about mounting your typical Gear Tracks, but in this case there are a couple things of consideration. The narrower GT90s are necessary because of the available width of the gunwale mounting surface on a Revo. Secondly the mounting location prevents you from being able to reach inside the hull for backing washers and nuts or use of Full-Backs, etc. The GT90 backing plates fit perfectly, but about the only way you can get them there is by “Fishing” them in there- such as done with the use of Yak-Attack (small 8-32) Rigging Bullets. Highly misunderstood, Rigging Bullets, are not mounting hardware at all but rather used as a tool! And what a handy tool those are!
b) Hobie Sideckick Ama Gear Track Adapters- Yak-Attack has the adapters to attach the Sidekick cross bar with a T-bolt and Nut for the Gear Track Mounting. Easy on and off, and no big 3/8” holes to worry about later. Easy peasy.
4) Main Sail Line- The main sail line is supposed to just go through the rear padeye (same one the carry handle is on) and the main sail line is just to be held in hand by the captain. Not very elegant, and a lot of loose rope! a) I have added Harken 29 Carbo pulley on a at the rear pad eye. Less friction, and much smoother! b) The main sail line routes back to the pulley, and through the starboard side tank well through the tie downs SS eyebolts that I have added. Nice and tidy! c) Just forward of the starboard Sideckick Ama mount goes a Spinlock PXR Cam Cleat to lock and control the main sail line. This is the item I would prefer to track mount. All I need is track nuts with 8-32 threads. The standard ¼-20 fasteners are too big to fit. So far, I have been unable to find 8-32 track nuts, so I will make my own in the near future. Ironically the devise bolt pattern fits exactly in line with the GT90 button head fastener spacing! I just used longer 8-32 stainless countersunk head screws, but this makes the mount somewhat “permanent”. This bugger is kind of spendy, but is a SWEET devise for this purpose!
I'm sure there's some Hobie sailors that would like something like this. I would also like to state for the record, I am not “PRO-Staff” or sponsored by anyone, nor have I received any promotional items for this write-up.
shougaler:
Thanks for doing this write up and posting pictures. I've been working on adding a similar mod. for my furler kit. I saw a great video that someone did on this on YouTube... but it was in German. So I find your parts list and directions very Germaine to the task at hand. Thanks!